Direct answer
- Crewson is a four-number line on our own site. The category publishes 21102, 21112, 22102 and 22103, and the previous/next chain confirms the set. The neighbouring families carry far longer lists, so Crewson is easy to miss when a buyer searches by number.
- None of the four product pages publishes a specification table. The Product Detail tab holds a description and a PDF link commented out in the page source. No thread, spline, caging, stroke or weight figure is published.
- The cast number and the catalogue number are not the same string. The 21112 body carries the raised marking FKH ASC21112, with 1 180524 beneath it, legible in the published photography.
- The Crewson feature list names Motor Wheel, not Crewson. That name appears three times on our Crewson series page and not at all on the Gunite or Meritor series pages.
- What is not published here is not optional. Federal inspection rules turn on the adjuster holding the brake inside the stroke limit, on both ends of an axle matching in effective length, and on an automatic adjuster never being swapped for a manual one.
Why the Crewson Line Sits Behind the Others
Distributors who order brake slack adjusters usually arrive with a number already written down. That number came off the casting of the part that came off the vehicle, because a shop read it from the housing. So the buying question is rarely “is this a good slack adjuster”. It is “does your catalogue carry the number on my bracket”, and that comes faster from a long list.
Crewson sits behind the others for that reason. The Crewson slack adjuster replacement range sits inside a family where the Haldex category lists six numbered items, the Meritor category eighteen R-code items, the Gunite category four AS-series items and the Bendix category four more. The 21112 OEM-quality replacement product and its three siblings are visible, but only to someone who already knows Crewson is a family name here.
The four numbers also invite a reading that is wrong. 21102, 21112, 22102 and 22103 look like a series digit, a variant digit and a size, and the previous and next navigation shows the assumption collapsing: 21102 sits between a Bendix number and 21112, and 22103 between 22102 and a Gunite number. The chain is a catalogue ordering, not a numbering scheme, so the digits carry no fitment information.
What Our Own Pages Publish About Crewson, and What They Leave Out
It is worth being precise about what is published, because the gaps are why this family gets overlooked. The Crewson series product page carries a full commercial block: FOB reference pricing of $19 per piece at 100 to 499 pieces, $18 at 500 to 999 pieces and $17 at 1000 and above, with samples at $30 per piece. The same block lists box or neutral packing, casting as the material, a one-year warranty, 100% tested quality, and lead times of 15 days at 1 to 500 pieces, 30 days at 501 to 2000, with 2000 and above negotiated.
Behind that block is a general description of the family and then the Features and Benefits list discussed below. There is no table. The Product Detail tab on each of the four Crewson pages holds the one-line description, a PDF link commented out in the page source, and the previous and next navigation. No thread size, no spline count, no caging geometry, no pushrod thread, no stroke figure and no vehicle application list is published.
That difference has a commercial consequence. A Haldex or Meritor number usually carries a published cross list, so the fitment argument can be made from the page. For a Crewson part the only published identifiers are the four numbers and the evidence on the casting, so the evidence becomes the specification.
The Four Numbers and What Is Cast Into the Metal

The published photography is unusually useful here, because it shows the cast markings clearly enough to read. On the 21112, the flank of the housing carries the raised marking FKH ASC21112, and beneath it 1 180524, a foundry mark and a date code of 18 May 2024. It appears in the featured image, the angled view and the detail view, so it is the marking on the part we ship.
Two things follow. The number cast into the metal is not the same string as the number in the catalogue. The catalogue calls this part 21112; the casting calls it ASC21112. A buyer matching against a photographed bracket, or reading the marking off a returned unit, will see ASC21112 and not find it in the catalogue. And the date code tells you when it was cast.
The photographs also make two points a specification table would normally make. Each part is a cast body with a gold-plated caging window exposing internal splines, a pivot control arm with a spring-loaded pawl and split pin, and a straight grease fitting at the top. The 21102, 21112 and 22102 each come with a white plastic adjuster wrench, and the 22103 is photographed with one. This is an automatic adjuster, not a manual one with a spring.
Why the Crewson Feature List Names a Different Brand
The Features and Benefits block on our Crewson series page is worth reading carefully. It opens by describing the product as Motor Wheel® Automatic Brake Adjusters, and lists eight named features: Auto-Check, for checking the air chamber stroke without crawling under the vehicle; Cam Guard, a lubrication system that eliminates seizing and corrosion between the S-cam and the adjuster; an Installation Guide; a Clearance-Sensing Adjuster System; a High-Strength Gearset; a Blue Powder Coat; a sealed gear; and a Pushrod Cutoff Tool.
Motor Wheel is not a brand we publish and not a family on our own site. The Gunite series page has no feature block like this one, and the Meritor series page carries a different one, built around a pull-pawl design, a sealed housing and a ratchet-type mechanism. Neither mentions Motor Wheel. This block was written for another manufacturer’s product line and left in place on ours.
I am not going to claim the features are wrong, because I cannot verify from our own pages whether this construction genuinely carries the Cam Guard system or the Auto-Check stroke indicator. What I can say is that a buyer reading our Crewson page is reading another company’s feature language, so the list is weaker evidence than it looks. Ask about the features on a trial order.
What the Inspection Rules Actually Require of the Part
This is what makes the missing specification table a problem rather than a curiosity. Whether a truck passes a periodic inspection in the United States is decided by the minimum periodic inspection standards in Appendix A to Part 396 of the Federal Motor Carrier Safety Regulations, and the slack adjuster is named in three.
The first is readjustment limits. The maximum pushrod stroke must not exceed the value given in the tables for the chamber type, and any stroke exceeding that limit is rejected. For actuator types not listed in those tables, the stroke must not be greater than 80 percent of the rated stroke marked on the actuator by its manufacturer, a rule set out at 49 CFR 393.47(e)(2). The number that decides whether an adjuster passes is the stroke the manufacturer marks, and that is the number our Crewson pages do not publish.
The second is matching parts across the axle. A mismatch across any power unit steering axle of air chamber sizes, or of slack adjuster length, is a defect in its own right, and the rule at 49 CFR 393.47(c) states it plainly: the effective length of the slack adjuster on each end of an axle must be the same.
The third is on automatic adjusters specifically. A failure to maintain a brake within the stroke limit specified by the vehicle manufacturer is a defect. Any automatic brake adjuster replaced with a manual one is a defect. And a brake found out of adjustment has to be evaluated to find why the adjuster is not working properly; it is not acceptable to manually adjust an automatic adjuster without first correcting the underlying cause. The full text is in Appendix A to Part 396.
So the part is judged on the stroke it holds, on its effective length against the adjuster on the other side of the axle, and on whether it is genuinely automatic and intact. None of that comes from a catalogue number, which is why I would not send a Crewson number out alone.
How to Order Crewson-Type Slack Adjusters Without a Misunderstanding
Six things, and they are the same for any of the four numbers.
- Send the number as it is cast, not as it is catalogued. If the housing reads FKH ASC21112, say that, and also say 21112 if that is what the paperwork calls it. Both are valid identifiers and not always the same string.
- Give the thread and the effective length. These are the two attributes that cannot be changed afterwards, and the effective length is the one the inspection rules measure. Ask for both in writing.
- Ask for the marked pushrod stroke for the model. This is the number the 80 percent rule applies to when the chamber type is not in the table, so it has to come from the part.
- Confirm the pairing across the axle. If you are replacing one adjuster on a steering axle, the effective length has to match the one on the other end, so check them as a pair.
- Say whether you need the adjuster wrench. The published photographs show a white plastic wrench supplied with these parts, worth having in the box for the first adjustment.
- Treat the feature list as a question, not a specification. If a feature matters to your customer, confirm it on a sample before committing a volume order.
Frequently Asked Questions
How many Crewson slack adjuster part numbers are there?
Four on our own site: 21102, 21112, 22102 and 22103. The category page lists those four Crewson-branded items plus the series product, and the previous and next navigation confirms the set. That is much shorter than the neighbouring families carry, so a buyer searching by number can pass this line unnoticed.
Is Crewson slack adjuster replacement the same as a cross reference?
No. A cross reference claims that one published number replaces another, and it needs published fitment data to support it. The Crewson pages publish none, so what we offer is the part itself, identified by its catalogue number and its cast marking.
What does the ASC21112 marking on the housing mean?
It is the marking cast into the body of the 21112 part as published in our product photography, with the letters FKH and the date code 1 180524 on the second line. We can confirm it is on the part and legible in the images; we cannot confirm what the ASC prefix refers to.
Why does the Crewson page talk about Motor Wheel brakes?
Because the Features and Benefits block on our Crewson series page was written for another manufacturer’s product line and left in place. The Gunite and Meritor series pages do not use that name at all. The description of the part we supply is accurate, but the named feature list is not ours to stand behind.
Can I replace an automatic Crewson slack adjuster with a manual one?
No. The minimum periodic inspection standards list any automatic brake adjuster replaced with a manual one as a defect in its own right, and a brake found out of adjustment has to be evaluated to find the underlying cause.
What do I need to send to get a Crewson slack adjuster matched to a vehicle?
Five items: the number as cast on the housing, the pushrod thread, the effective length of the adjuster being replaced, the vehicle application with the drum size, and the brake chamber type, because that determines which readjustment limit applies. You can request the full product catalog (2).
What are the published prices and lead times for this line?
On our Crewson series product page the FOB reference pricing is $19 per piece at 100 to 499 pieces, $18 at 500 to 999 pieces and $17 at 1000 and above, with samples at $30 per piece. Lead time is 15 days at 1 to 500 pieces, 30 days at 501 to 2000, and negotiated above.
Talk to Our Team About Crewson-Type Slack Adjusters
Send the number as cast on the housing, the thread, the effective length and the vehicle application, and we will come back with the part confirmed against our current catalogue and the published lead time band for your quantity. We would rather ask two questions than quote a part that fails an inspection on the ramp.
About the author
Elian Zhou — Export Manager, Shaoxing Fangjie Auto Accessory Co., Ltd. Elian Zhou is Export Manager at Shaoxing Fangjie Auto Accessory Co., Ltd., a truck brake system components manufacturer with over 20 years of OEM production experience since 2003. Based in Shaoxing, Zhejiang, he works daily with the company’s 100+ workforce and 10-person foreign trade team to supply brake calipers, slack adjusters, solenoid valves and brake chambers to aftermarket distributors across Europe, Southeast Asia and the Middle East. He visits the factory floor and shares production insights on YouTube.
Last verified: 2026-11-17. The four Crewson product numbers, the catalogue ordering between them, the cast markings visible in the published photography, the FOB reference pricing, sample price, packing, material, warranty, quality statement and lead time bands are as published on the corresponding product and category pages of this website. The Crewson feature list quoted above names Motor Wheel Automatic Brake Adjusters, as published, and the absence of a specification table on the four Crewson product pages is as published. Regulatory references are to Appendix A to Part 396 and to 49 CFR 393.47 of the Federal Motor Carrier Safety Regulations, as published on eCFR. Procurement and interchangeability guidance only, not a certification or type approval; every fitment must be confirmed against current product data and the vehicle and destination market requirements before ordering.
Post time: Nov-17-2026
